Showing results: 391 - 405 of 422 items found.
-
1908 Series -
Aim-TTi
The battery operation can give more than 35 hours of operation. As well as adding portability to the unit the battery option provides isolation from the mains to aid low level measurement integrity. The USB interface is fully accessible in battery mode, allowing full data logging when used with a laptop pc. The dual measurement display shows the main and secondary reading simultaneously to provide either two parameters of the same signal (eg AC and DC Volts), two different signals (e.g AC Volts and DC current), the result and calculated function (eg value and % deviation), two different units (eg AC Volts and dBm) or the measurement along with the selected range.
-
Keysight Technologies
PCI Express® technology is implemented broadly in systems requiringhigh-speed data transfer, such as video or graphics.Keysight's PCIe protocol solutions provide a complete PCIe 5.0 test path with a PCIe protocol analyzer and a PCIe exerciser. The integrated design boosts signal integrity and provides outstanding verstaility.Keysight's protocol solutions enable faster, more confident testing of PCIe designs, now and in the future.
-
CENSUS Series -
Multidyne
Working with audio is a complex endeavor. There are broadcast compliance challenges, ensuring that audio loudness thresholds are not exceeded. There are the quality control essentials that assure broadcast signal integrity. Depending on format, the number of signals to monitor and maintain range from very low to high density. MultiDyne acquired Census Digital in 2020 to problem-solve these broadcast and production audio challenges. MultiDyne’s rackmounted CENSUS Series provide reliable confidence monitoring for studios, mobile production and broadcast operations. Each addresses signal density needs for SDI, analog, AES/EBU,MADI or Dante IP audio, and simplifies how engineers visually and aurally monitor individual audio channels, adjust loudness levels and downmix channels. A consistent front panel design and intuitive UI assures a familiar user experience across all models while extracting audio information, setting key parameters and maintaining quality control.
-
D9010AUTP -
Keysight Technologies
- Set up your scope to show CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT protocol decode in less than 30 seconds- Support CAN XL protocol trigger and decode of the SIC mode (or slow mode) signal in the arbitration phase as well as the FAST mode signal in the data phase- Get access to a rich set of integrated software-based protocol-level triggers- Save time and eliminate errors by viewing packets at the protocol level- Use time-correlated views to quickly troubleshoot serial protocol problems back to their timing or signal integrity root causeThis application (for Infiniium Oscilloscopes) includes a suite of configurable protocol-level trigger conditions specific to CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT. When serial triggering is selected, the application enables software-based triggering. Application supports CAN-dbc symbolic debug.
-
PXIe-1803 -
Astronics Corporation
This 130/180 MS/s Dual Channel PXI Express digitizer provides the best speed and performance available for input frequencies up to 175 MHz.With exceptional signal integrity, high density and modularity, and channel synchronization options, this new digitizer provides massive functionality in a compact form factor.Key features include:Dual 14/16-bit digitizer configurable as separate or fully synchronized channelsWaveform bandwidths of 65-175 MHz (typical)64M words of waveform memory per channelExternal clock input for synchronization up to 180 MHz250 μV Measurement AccuracyNoise Floor and RelativeAccuracy as Precise as 0.006%
-
NI
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
SMPTE-HUT Series -
Multidyne
We work in an industry of hybrid workflows and solutions, but sometimes we need authentic innovation that changes how we work. MultiDyne’s next-generation SMPTE-HUT Series is the definition of a pure solution that elevates the live production workflow. SMPTE-HUT universal camera transceivers free SMPTE-based camera chains from the limitations of hybrid copper and fiber cabling, and removes interferences associated with copper connectivity. Camera operators instead have a plug-and-play system that requires only two stands of single-mode fiber - reducing costs, weight, and set-up times – while ensuring the best possible signal integrity. With options to multiplex camera signals, boost the optical range of cameras and regenerate optical power over fiber, SMPTE-HUT is a purist’s solution for remote broadcasting, sports production and other long-distance SMPTE studio camera applications.
-
Ironwood Electronics
For BGA, QFN, or LGA applications, GTP contact technology provides >94 GHz signal speed and can additionally be used in high cycle life applications such as ATE. These sockets support pitches from 0.2 mm to 1.27 mm. Ironwood's GT sockets are ideal for prototyping and testing almost any BGA device application. These IC sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss (1dB at 94GHz) and supports BGA packages with pitches down to 0.2mm was utilized in these sockets. GT BGA sockets are mechanically mounted over a target system's BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry's smallest footprint).
-
RP4030 -
Teledyne LeCroy
The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:-Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing- Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOsThe RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.
-
Virginia Panel Corporation
Our customers have shared a long history of using printed circuit boards (PCB) in the interchangeable test adapters (ITAs) of their automated test equipment (ATE) stations. Whether you are designing a self-test fixture, looking to save space, improve signal integrity, or reduce cable management concerns, Virginia Panel Corpoation has a team of engineers to help you design, manufacture, and integrate PCBs into your ATE system.
-
Smiths Interconnect
The proprietary MicroClip™ is a low-profile, low-mass spring loaded mechanical assembly that offers a rugged optical connection that is resistant for shock and vibration and is suitable for harsh environment. The MicroClip ferrule design has proven it can withstand a 1 kg live traffic fiber pull test on a 12-fiber ribbon cable pigtail mated to its LightABLE™ products (40G SR4 and 120G SR12), without any signal performance degradation. This result exceeds by a factor of 2 the requirements of Telecordia GR-468-CORE Fiber Integrity Side Pull Test and confirms the reliability of the Reflex Photonics fiber ribbon interface with the LightABLE and its MicroClip ferrule.
-
778572-10 -
NI
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
BAW -
Macom Technology Solutions Holdings Inc.
MACOM’s BAW product portfolio is ideal for high performance Industrial, Aerospace, Defense, and Communications applications that require critical frequency filtering. Our high-performance RF filters enable our customers manage signal integrity in the 1 to 6 GHz frequency range. Bulk Acoustic Wave Resonators consist of two metal electrodes above and below a layer of a piezoelectric material. The piezoelectric material converts an electrical signal to a mechanical signal and vice versa. The metal electrodes provide the connections to/from the piezo material. The frequency at which resonance occurs depends on the thickness of the combined metal-piezo-metal stack. Advances in thin-film piezoelectric fabrication have enabled BAW resonators to meet RF filtering challenges up to 6000 MHz using standard MEMS fabrication process. High-performance BAW resonators-based RF filters are made of piezoelectric material having high Q-factor (>3000) and high coupling coefficient. Currently, no competitive technology provides the same high performance for RF filter applications when compared to BAW resonator-based RF filter up to 6000 MHz for the same size and cost.
-
Ironwood Electronics
Ironwood has the most comprehensive collection of BGA (Ball Grid Array) sockets that can be used for prototype application, silicon validation, system development, thermal characterization, burn-in application, functional production test, etc. BGA socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. BGA sockets for prototype applications, silicon validations, system development applications uses low cost elastomer contact technology.
-
Ironwood Electronics
*Package-size PCB footprint: Since the PCB footprint of Grypper is identical to the package, only one PCB design is required, enabling a seamless transition from test and validation through production and reducing overall cost of test*Low insertion force: Unique contact design reduces the insertion force required to insert and retain higher-ball-count packages safely and securely within the test socket*Oxide cutting wipe action: The contact design wipes the side of the solder ball during insertion, breaking through solder oxides ensuring a good electrical connection between contact and solder ball*Signal integrity: A short signal path achieves low inductance and low insertion loss, providing a nearly invisible electrical connection*Test socket has solder balls attached: The G40 contacts have solder balls reflowed onto the contacts to ensure reliable solder volume at the PCB to test socket solder interface.
